Jacquard White Coating
video

Jacquard White Coating

Elegant Textured Roller Blind Material | Custom White Coated Fabric Manufacturer in China
Products name: LS23014
composition: 100% Polyester
width: 300cm
weight: 440g/m2
Send Inquiry
Product Introduction

Jacquard White Coating Roller Blind Fabric - LS23014

 

Jacquard White Coating
Jacquard White Coating
Jacquard White Coating
Jacquard White Coating

100% polyester jacquard base fabric with white foam or acrylic coating on the reverse. 100% blackout. Width up to 300 cm as standard. Flame retardant to NFPA701 on request. Supplied as fabric roll goods only - no finished blinds.

 

 

Product Specifications

 

Parameter Data
Article No. LS23014
Base fabric 100% Polyester, yarn-dyed jacquard weave
Coating (reverse) White foam coating or acrylic coating
Weight 440 g/m²
Standard width 300 cm
Custom width range 150 cm – 320 cm (widths above 320 cm subject to prior capacity confirmation)
Shading rate 100% blackout
Flame retardancy NFPA701 as standard option; other standards quoted on request
Coating colour White as standard; coloured foam coating available (acrylic coating cannot be supplied in dark shades)
Order type OEM and ODM accepted
Supply form Fabric rolls only

Weight and width data refer to the finished coated fabric. Shading rate is measured on the coated side against visible light transmission.

 

 

Coating and Functional Options

 

 

Blackout level

100% blackout as standard on this article. Semi-blackout (50–60%) and standard blackout (70–80%) are available on other polyester jacquard constructions if the project does not require full opacity.

 
 

Flame retardancy

NFPA701 is the default flame-retardant specification quoted for LS23014. BS 5867, BS 13773, and other project-specific standards can be evaluated against the base fabric and coating combination; confirm the target standard before sampling so the correct back-coating formulation is used.

 
 

Water repellency

A water-repellent finish can be applied in place of, or in addition to, the standard foam coating. This is quoted as a separate option and is not part of the default LS23014 specification.

 
 

Coating adhesion

The coating is applied and cured under controlled tension. Coating adhesion is checked as part of routine in-process inspection; delamination and blocking are the two failure modes we monitor most closely on foam-coated jacquard.

 

 

 

Quality Control on This Article

 

Grey fabric inspection before coating: warp/weft density, weft skew, and surface defects.

Coating weight and coating uniformity monitored during production.

Finished roll inspection

Shade continuity against the approved sample, coating adhesion, and visual blackout check.

Colour fastness

Light fastness and wash fastness tested against the agreed standard before bulk release. Confirm the required fastness rating at sampling stage if the end use involves direct sun exposure or frequent cleaning.

Production runs under an ISO 9001 quality management system. Annual sunshade fabric capacity across the coating lines is 4.5 million meters.

Certificates and test reports are issued against the specific article and coating combination. If the project requires third-party testing or a particular declaration, state this before the sample is made so the correct test specimen can be prepared.

 

 

Typical Applications

 

Jacquard White Coating

Roller blinds in hotel guest rooms and serviced apartments where full blackout and a woven face are both required.

Jacquard White Coating

Residential bedrooms and media rooms specifying 100% blackout with a fabric face rather than a plain coated cloth.

Jacquard White Coating

Commercial office roller blinds where a heavier coated jacquard is preferred for roll-up consistency and surface durability.

Jacquard White Coating

Projects specifying NFPA701 flame retardancy alongside blackout performance.

The fabric is supplied to blind manufacturers, contract fabricators, and distributors. It is not a retail cut-length product.

 

 
Product Parameter

 

Products name LS23014

Product style

customized

Product raw material

fabric+foamcoating/arcylic

Shading rate

100%

Flame retardant

NFPA701or customized

Color

arcylic (can not be dark col)

Application

Roller Blind Fabric

OEM&ODM

ACCEPT

 

 

Why This Construction

The base cloth is woven on a jacquard loom using yarn-dyed polyester. Colour is applied to the yarn before weaving, not to the finished cloth. This allows the face and reverse of the jacquard structure to be matched in tone or contrasted deliberately, without relying on piece-dyeing after coating.

The 440 g/m² coated weight is on the heavier side for a roller blind fabric. It gives the cloth a dense hand and a flat hanging behaviour. In roller blind fabrication, heavier coated jacquard reduces the risk of edge curling and gives the blind a more uniform roll-up diameter across the width.

 

The reverse coating is white foam as standard. Foam coating produces an opaque, light-diffusing back face without the reflective sheen of a silver or metallic coating. Where a coloured reverse is required for a specific interior scheme, coloured foam coating is available. Acrylic coating is supplied white only - dark acrylic shades are not offered on this article because of coating adhesion limits.

 

Jacquard pattern control. The three-dimensional effect comes from the weave structure itself, not from embossing or printing. Pattern repeat, scale, and colour arrangement are set at the weaving stage. We can develop jacquard patterns from customer artwork or existing samples; geometric, stripe, and small-repeat dobby effects are within the range we routinely run.

 

 

 

Full Shading

 

Semi-Shading

 

Tough Material, Can't be Torn!

 

Width and Ordering

 

Standard production width is 300 cm. The jacquard base can be woven and coated across 150 cm to 320 cm without a horizontal seam in most patterns. Widths beyond 320 cm require a capacity check at the coating line before order confirmation - do not assume availability.

 

Fabric is supplied on rolls for blind makers and fabricators. We do not sew, weld, or assemble finished roller blinds. Cut lengths, roll put-up, and packaging format are agreed at order stage.

 

MOQ depends on article, colour, and coating specification. For LS23014 in standard white, small trial orders can be discussed; coloured foam coating and custom jacquard patterns carry a higher minimum because of yarn preparation and loom set-up. State the target quantity with the initial inquiry so the MOQ can be confirmed against the coating batch size.

Lead time is 45–60 days from order confirmation for standard specifications, adjusted by order volume and coating schedule. FOB is the default trade term. Sea freight is standard; air and land arrangements can be quoted on request.

 

Factory Address:
Yunhebei Industrial District, Dama Town, Tongxiang City, Jiaxing City, Zhejiang Province.

 


 

R&D Capacity
OEM, ODM

 


 

R&D Staff
5-10 People

 


 

Production Lines
Above

 


 

Annual Output Value
US$5 Million - US$10 Million

Factory

 

Factory Showcase

 

Production Process

 

 

 

Our exhibition

FAQ

 

Q: Can the jacquard pattern be changed without changing the coating?

A: Yes. Pattern and coating are separate process steps. A new jacquard pattern requires new yarn arrangement and loom programming, but the white foam or acrylic coating specification can remain unchanged. Pattern development is quoted separately from coating.

Q: What is the difference between the white foam coating and the acrylic coating on this article?

A: Foam coating gives a denser, more opaque back face and is the standard route for 100% blackout on LS23014. Acrylic coating is lighter in hand and is used where the coating needs to remain white and flexible, but it cannot be supplied in dark shades. Both can be specified to NFPA701.

Q: Can you supply this fabric with BS 5867 instead of NFPA701?

A: BS 5867 can be evaluated on the polyester jacquard base with a modified back-coating formulation. It is not a drop-in substitution for NFPA701 - the coating chemistry differs. State the exact standard and classification at inquiry stage; sampling will be against that standard, not against NFPA701.

Q: What is the MOQ for a custom jacquard pattern in a non-standard width?

A: Custom jacquard and coloured foam coating both raise the minimum order. As a working reference, custom jacquard patterns typically start at a higher meterage than the standard white article because of loom set-up and yarn minimums. Provide the target width, colour direction, and estimated order quantity, and the MOQ will be confirmed against the actual weave and coating batch.

Q: Do you supply finished roller blinds made from LS23014?

A: No. LS23014 is supplied as coated fabric in roll form. Cutting, hemming, tube insertion, and blind assembly are carried out by the blind manufacturer or fabricator. We can discuss roll length and packaging to suit the customer's cutting line, but the output is fabric, not a finished blind.

 

Get a Factory Quote Now

 

Tags:Jacquard white coating roller blind fabric, jacquard roller blind material, polyester jacquard coated fabric, white coated window fabric, roller blind fabric manufacturer, jacquard blackout fabric, custom roller blind fabric, China fabric factory, coated jacquard shade materia

 

Hot Tags: jacquard white coating, China jacquard white coating manufacturers, suppliers, factory, 600 600oxford White Coating, 150 300oxford Transmitting, Blackout Roller Blinds, Jacquard Cross Bamboo White Coating, Plain Blackout Fabric, Roller Blind Sun Protection Fabrics

Send Inquiry

whatsapp

Phone

E-mail

Inquiry