100% Coating Blackout Fabric
Composition:100% Polyester
Width: 280/cm-300/cm
Weight: 260g
LSFH2401 Double-Side Composite Blackout Coating Fabric
The base fabric is 100% polyester. The coating is an acrylic foam system applied in a double-side composite construction - not a single-surface back coating. "Double-side composite" here refers to the coating build across the fabric, not to a laminated film between two separate face layers.
Coating-side orientation matters at cutting and sewing. Confirm which face is the coating face against your finished-goods requirement before laying out the cut. The coating face behaves differently under needle penetration and presser-foot friction compared with the uncoated face; stitch density and needle size should be set on a sewn sample, not extrapolated from an uncoated polyester.
On specification
The 260 g/m² figure is nominal. Finished weight, coating add-on and usable width tolerance are stated in the technical data sheet current at the time of quotation. Usable width is not the same as the listed 280–300 cm range - edge allowance and dimensional tolerance determine the cuttable width. Calculate cutting layouts from usable width, not from the nominal range.
Acrylic color limitation
The standard acrylic coating system does not support dark colors. If the project color falls outside the standard acrylic range, state the target at inquiry; feasibility is reviewed against coating route and order quantity. Lab-dip or strike-off approval is required before bulk production.
Where it goes on the production floor
Curtain manufacturing
This fabric is used as a face fabric where light control comes from the substrate, not from a separate lining. At the cutting table, confirm coating side relative to the face. At sewing, set stitch length and needle on a sewn sample: the coated face can show needle marks and feed-dog tracking that are not visible on the uncoated side. For pleated or gathered headings, confirm that the finished drop stays within the usable width after heading take-up. For flat-panel construction, seam type and seam position relative to the coating face should be agreed before bulk cutting.
Roller blind fabrication
Confirm the fabric runs on the intended roller system before bulk. Relevant variables: which face contacts the tube, roll-up direction, surface friction at the coating side, and whether the finished weight and thickness sit within the tube and bracket specification. Edge stability and surface consistency should be checked during sampling, not assumed from the roll.
Commercial window covering projects
For hotel, office and other contract work, the project specification should name the required dimensions, color reference, shading performance and applicable test standard before product suitability is confirmed. Where NFPA 701 or another destination-market standard applies, identify the standard and the country of installation at quotation so that report scope can be confirmed. A report for one standard does not automatically cover another.
Product Parameter
| Products name | LSFH2401 |
|
Product style |
customized |
|
Product raw material |
fabric+foamcoating/arcylic |
|
Shading rate |
100% |
|
Flame retardant |
NFPA701or customized |
|
Color |
arcylic (can not be dark col) |
|
Application |
Double Side Composite Blackout Coating Fabric |
|
OEM&ODM |
ACCEPT |
What is checked, and where
Coating weight, width and surface appearance are checked at the coating line. Batch retain samples are kept for repeat-order comparison. Pre-shipment checks cover fabric appearance, dimensional verification against the agreed usable width, roll packaging and labeling.
Defect categories reviewed before shipment include coating skips and scratches, shade continuity across the roll, edge condition, pinholes and roll-winding consistency. Buyers with a defined inspection protocol can submit it at quotation; compatibility with our in-house check points is confirmed before the order is accepted.
Third-party test reports, compliance declarations and project-specific inspection documentation are handled at quotation, not assumed from this page. Availability depends on the standard, the destination market and the batch. The applicable report scope is confirmed in writing before bulk production.
What can be changed, and what cannot
The following are reviewed for project-specific adjustment, subject to construction, order quantity and production route:
- Usable width and roll length
- Coating color within the acrylic system limitation
- Flame-retardancy standard and the documentation package tied to that standard
- Packaging and labeling
Full Shading
Semi-Shading
Tough Material, Can't be Torn!
For quotation, send these
Required usable width and nominal weight
- Fabrication method: curtain, roller blind, or other
- Coating-side requirement, if the finished product has a defined face and back
- Color reference or approved swatch
- Estimated order quantity
- Destination country and applicable test standard, if any
- Roll length and packaging requirements
Send the project specification and quantity; the reply covers the TDS current at quotation, sample availability and the specification points that need confirmation before a price can be issued.
Factory Address:
Yunhebei Industrial District, Dama Town, Tongxiang City, Jiaxing City, Zhejiang Province.
R&D Capacity
OEM, ODM
R&D Staff
5-10 People
Production Lines
Above
Annual Output Value
US$5 Million - US$10 Million
Factory Showcase
Production Process
Honor And Qualification
Our exhibition
FAQ
Q: What is the composition of LSFH2401?
A: The currently listed base fabric composition is 100% polyester. The complete coating composition and finished fabric construction should be confirmed with the manufacturer.
Q: What is the available width?
A: The listed nominal width range is 280–300 cm. Please confirm usable width and tolerance before finalizing cutting plans or order quantities.
Q: What is the weight of this blackout coated fabric?
A: The listed weight is 260 g/m². Buyers should confirm the nominal value and applicable tolerance against the latest technical data sheet.
Q: Can the blackout performance be specified for a project?
A: Yes. Buyers can provide the required light-control level and applicable test method. The manufacturer should confirm whether the selected product meets the requirement and whether supporting test documentation is available.
Q: Can I request a sample before placing a bulk order?
A: Contact Lishun Textile to confirm sample availability, sample dimensions and shipping arrangements. Please provide your intended application and required specifications.
Hot Tags: 100% coating blackout fabric, China 100% coating blackout fabric manufacturers, suppliers, factory
You Might Also Like
Send Inquiry